Basket

Ø 15 mm mit Außengewinde M 10.
(Bei Trimmsäge Nr. 1100 enthalten)

1 l Tribosynt.
Coolant lubricant increases the standing life time and the cutting performance of the saw blade and may be used multiple times.
It has a pleasant odor and for sawing is diluted in a mixing ratio coolant 1 : 10 water.

For grinding, polishing, brushing, milling, drilling, engraving, retouching. Also for mounting of putty pens to work gemstones.

For working of difficult to access locations if the dimension or the weight of the workpiece requires the use of a bendable shaft.
Equipped with keyed chuck 1 - 10 mm clamped. Cord inside of diameter 8 mm made of 6 layers steel. Rotational direction right, maximum 8000 rotations per minute. Axle in the handle. Driving element with ball bearings.

Flexible shaft with chuck 1..10 mm, adapter with threaded hole for mounting on LAPIDA machines and the multi-faceting unit of Multimotors.

Precision drill chuck on flange.
Keyed chuck for receiving of grinding and polishing or diamond bodies.
For Multimotors and Special countershafts with shaft diameter 15 mm.
With quick clamping flange 1..10 mm, 1..13 mm or 3..16 mm.

Fitting to MULTI-Motors EXPORT and SIMPLEX or the Special countershaft. It can be attached to both sides of the motor.

Quick clamping flange zinc coating galvanized and yellow passivated for 2 grinding or polishing discs at the same time, suitable for Multi-Motors and Special countershafts with shaft diameter 15 mm.
All our quick clamping flanges allow a disc change within seconds, without renewed truing off or balancing.

for multimotors Export and Simplex or special countershaft. For polished section, thin section, spherical grinding.
Suitable for stones up to (5 x 5) cm.
Disc diameter 150 mm.
Includes carrying disc for polishing discs, with driven wheel on quick clamping flange, stainless shaft, 2 ball bearings. Thread M 13x1.5 right. 

By moving the drive wheel on the motor shaft and due to the motor with 2 speeds  - (700 | 1400) U/min - every arbitrary number of revolutions between 300 revolutions per min and 1200 revolutions per min can be set on the horizontally running disc.

The area and faceting unit can be mounted on both sides of the motor using a clamping screw. At this the left side should preferably be used for polishing because because screwed on discs, like for example the cast iron disc, may get loose.

Complete with with carrying disc and disc mounting parts, drive wheel on flange, motor mount, supporting surface for facet heads and water drain connection 1/2".

For grinding, polishing, brushing, milling, drilling, engraving and retouching. Also for mounting of putty pens for working gemstones.
For working difficult to access locations, if the dimensions or the weight of the workpiece require the use of a bendable shaft.
Equipped with a keyed chuck clamping 1..10 mm,
inside cord with diameter 8 mm made of 6 layers steel. Rotational direction right, maximum 8000 rotations / min. Axle in the handle and driving element with ball bearings.

Flexible shaft with chuck 1..10 mm, adapter with center hole 15 mm diameter. For attachment to MULTI-motors, special countershaft and ball bearing countershaft.

For sawing and fine grinding of thin sections on the glass support to few hundredth milli meters thickness, with diamond discs or a cast iron disc with grinding powders.
The thin sections are used for photo slides or micro-photographs.

Suitable for all Lapida machines, the multi-faceting unit of the multimotors and for device of different type of construction. The thin section arm rails with an adjustable brass bushing on a thrust (purely axial or axial-radial) bearing.

Complete with foot stand, Holding bar diameter 20 mm, axial bearing and height fine tuner stainless steel, 10 glass support sheets (27 x 46) mm and bolts M10 for fixing including washers.

Faceting head with angle scale and pointer, height adjusting mechanism, base and holding bar diameter 15 mm, stainless.
The 16 partitions disc is adjustable and suitable for all facet cuts with index 64 (shaft diameter of the Dopp pin 8 mm).
The board may be polished without reclamping with 0 degrees (see instructions in the book "Edle Steine schleifen").

Can be mounted to all HAMAG gemstone grinding machines as well as machines of different construction.

Includes base, holding bar 15 mm Ø and height fine tuner, 16 partitions disc and bolts M 10 for fixing.

This accessory to the shape grinder is indispensable if the shape grinder is to be used for grinding at vertically running discs
(left side of the LAPIDA or other machines).

Please enter the diameter of the holding bar!

For the precision multi-faceted head.
Partitions 22, 60, 63, 64 (bei Facettenkopf enthalten), 96

(new model) for precise re-attachment and re-orientation of stones.
Made of cast Aluminium with V-grooveand Dopp-pin-attachments.
New is one rigid and one movable putty pen lock mechnism, such that the stone can be repositioned and oriented precisely and without torsion.

This extension made of Aluminium screwed below or ontop the support for the multi-faceted head of the Lapida machine to be able to grind the grindle (Rundiste) at an angle of 90 degree.

Dimensions: 100 x 30 x 15 mm

Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.

Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.

Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.

Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.