Dopp pin single special dimensions
Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.
from 1 from € 6.20 Incl. 19.00% VAT
Grinding disc SiC
Made of silicon carbide (SiC).
Outer diameter 150 mm, center hole 20mm or 32 mm Ø, width 20 mm.
Reductions to other shaft diameters available (price on request).
from 1 from € 30.00 Incl. 19.00% VAT
Cast iron lapping disc
150 mm diameter, for polishing sections and facet cut with loose Silicon carbide suitable for all "HAMAG" Lapida-Machines and the Multi-faceting unit for Multimotors.
No center bore, thus grinding using the disc center possible. Inner thread M13 x 1,5 right.
from 1 from € 52.10 Incl. 19.00% VAT
Diamond dresser Hammer shape
zum Abrichten von Siliziumkarbid - oder Korundscheiben aller Art.
Diamantabrichter D 602, Körnung 30/40, Handaufnahme 125 mm lang, Abrichtfläche 10 x 45 mm
from 1 from € 56.70 Incl. 19.00% VAT
Grinding powder silicon carbid: 2220,2222,2225,2230,2231,2240,2252,2255,2260,2261,2270The grinding powder is mixed with a little water in a bowl and applied to the disc with a brush.
Applicable to cast iron, steel discs or drum machines.
from 1 from € 3.60 Incl. 19.00% VAT
150mm Ø, with sponge rubber covering. Without center hole. Inner thread M 13 x 1.5 right.
For sticking on of waterproof grinding discs for roughing and finishing touches of Cabochons and smaller minerals.
Fitting to all "HAMAG" gemstone grinding machines.
from 1 from € 30.50 Incl. 19.00% VAT
150 mm diameter, water proof, for the aluminium disc with sponge rubber covering.
from 1 from € 0.50 Incl. 19.00% VAT
Permanent adhesivefrom 1 from € 9.90 Incl. 19.00% VAT
Tin lead insertfrom 1 from € 19.20 Incl. 19.00% VAT
Acrylic glass insert
85 mm x 3.5 mm thick, bore diameter 1/2"
from 1 from € 11.35 Incl. 19.00% VAT
85 mm x 3.5 mm thick, bore 1/2"
from 1 from € 34.00 Incl. 19.00% VAT
Lead insertfrom 1 from € 20.40 Incl. 19.00% VAT
Filt discfrom 1 from € 12.40 Incl. 19.00% VAT
Leather polishing disc
for Lapida and Faceting device.
Cattle leather 4..5 mm thick for polishing of particular materials.
Should be used with a carrying disc, e.g. Aluminium carrying disc article number 1940 or Acrylic glass disc.
Diameter 150 mm, bore diameter 1/2 "
from 1 from € 18.60 Incl. 19.00% VAT
for Lapida and Multi-faceted unit.
For the polishing of bevels till HM 5..7, diameter 150 mm, center hole 1/2 ".
from 1 from € 58.80 Incl. 19.00% VAT
for Lapida and Faceting device.
For multi-facet polishing up to HM 8, alloy tin 50 : 50 lead, diameter 150 mm, bore diameter 1/2 ".
from 1 from € 55.70 Incl. 19.00% VAT
Kupferscheibefrom 1 from € 107.00 Incl. 19.00% VAT
Plexiglasscheibefrom 1 from € 16.50 Incl. 19.00% VAT
Holzscheibefrom 1 from € 17.70 Incl. 19.00% VAT
Stirnholzscheibefrom 1 from € 38.90 Incl. 19.00% VAT
Holzscheibe zur Verwendung auf Flanschenfrom 1 from € 21.00 Incl. 19.00% VAT
Filt discfrom 1 from € 21.00 Incl. 19.00% VAT
Schwabbelscheibefrom 1 from € 15.60 Incl. 19.00% VAT
Polishing powder Aluminium oxideThe polishing powder is mixed with a bit water in a bowl and is applied with a brush to the polishing discs.
Al-oxide for all kinds of stone.
from 1 from € 2.60 Incl. 19.00% VAT
Polishing powder Cer-oxidefrom 1 from € 8.15 Incl. 19.00% VAT
Diamond cut disc mechanicalDiamond grain pressed mechanically.
These affordable cut discs suit especially cutting of gemstones up to hardness levels 7 to 8.
Please choose desired disc diamaeter, cover thickness, cut width and drill diameter.
from 1 from € 25.20 Incl. 19.00% VAT
Diamond cut disc sintered: 1740,1750,1760,1770,1780,1790,1800,1810,1820,1830,1840,1850,1860
Diamond grain in bronze bond.
These cut discs suit optimally to cut all minerals and stones. They have a very high lifetime and result in very clean cuts.
The coating thickness is 10 mm.
from 1 from € 77.70 Incl. 19.00% VAT
Galvanic hollow drill bit
Because the drill bit is made completely of diamond granules, the life-time compared to other only coated (and that sparsely) diamond bits is hundred-fold higher, because the drill can be used till the end.
(A merely coated drill is worthless once the few diamond granules at the front side are broken out.)
The shaft is cylindrical with the respective drill diameter.
Drill length approximately 30..40 mm.
Can be clamped into every chuck.
Without holder and ejector.
from 1 from € 40.00 Incl. 19.00% VAT
Diamond hollow drill sintered(Diamond grain in bronze bond)
Drilldepth standard 40 mm.
Thickness coating 6 mm, wall 1 mm.
Machine clamp system Belgian thread R 1/2".
Diamond concentration C 75.
Drill depth on diameter 6 mm up to 160 mm deliverable (request price)
Drill depth on diameter 10 mm up to 200 mm available (request price)
Drill depth on diameter 20 mm up to 250 mm deliverable (request price)
Other drill depth on diameter 180 mm up to 250 mm on request.
These drills can be delivered with approximate diameter 13 mm with cylindrical shaft (€ 6,- extra cost).
from 1 from € 83.00 Incl. 19.00% VAT
Drill flushing head
Small drill flushing head for diamond drills 0.7..10 mm diameter.
Can be clamped into common commercially available bench drills with chuck and is compatible for drilling machines with holder and ejector. The mounting shaft is 6 mm.
from 1 from € 179.00 Incl. 19.00% VAT
Wasseranschluß mit Schlauchfrom 1 from € 14.40 Incl. 19.00% VAT
Diamond drill with holder and ejector: 4300,4310,4320,4330,4340,4350,4360,4370,4380,4390,4400,4410,4420,4430,4440,4450,4460,4470
The bit is of diamond grain, such that the life time is not comparable with other only coated bits.
These drills have a hundred-fold life time if compared against others because the drill bit can be used till the end. (A merely coated drill is worthless once the few dimond granules on the front side are broken out).
Shaft with respective drill diameter 30 mm long and at the back a thread of M4.
Can be screwed in flushing head (article number 4200).
from 1 from € 26.00 Incl. 19.00% VAT
Aluminium support disc
To article numbers 1941..1947.
Aluminium carrier disc with diameter 150 mm, 8 mm thick and center hole 1/2".
Required only for the diamond discs made of 1 mm steel sheet.
from 1 from € 30.50 Incl. 19.00% VAT
Galvanische Diamantschleifscheibefrom 1 from € 60.00 Incl. 19.00% VAT
Galvanische Diamant-Schleifscheibe D*from 1 from € 0.00 Incl. 19.00% VAT
Perforated diamond disc galvanic for thin sectionfrom 1 from € 155.00 Incl. 19.00% VAT
Galvanic Diamond Grinding disc S
Dimensions: 150 mm (outer diameter) x 32,5 mm (cover width)
With this heavy steel disc the diamond granules are bonded in a layer of nickel.
The center bore by default is 1/2" (12.7 mm), can be changed on request.
Diamond discs allow a clean grinding, because water is used only dropwise.
There is a recess in the center in which the different polishing inserts article numbers 2000..2030 may be placed.
Different grain sizes available.
Price on request!
from 1 from € 0.00 Incl. 19.00% VAT
Diamond faceting disc D* sintered
Sintered Diamond disc, where the Diamond granules are embedded in a 0.5 mm thick Bronze cover. Thereby the life-time is significantly increased compared to galvanically bound discs.
Outer diameter 150 mm; Cover width: 32,5 mm. The center hole is 1/2" (12,7 mm) by default, and can be changed on request.
Allows a clean grinding, because water is only used dropwise.
In the center is a recess, in which the different polishing inserts article numbers 2000..2030 can be fitted.
Different grain sizes available.
Preis auf Anfrage!
from 1 from € 340.00 Incl. 19.00% VAT
Sharpening stonefrom 1 from € 21.00 Incl. 19.00% VAT
Diamond paste with natural diamonds: 2190,2191,2192,2193,2194,2195,2196,2197,2198,2199,2200,2201,2202,2203,2204,2205,2206,2207,2208,2209,2210,2211,2212,2213
Concentration N (high diamond concentration)
oil / lapid soluble.
For finest polish of gemstones.
from 1 from € 39.00 Incl. 19.00% VAT
Polishing motor BAA workbench motor
A versatile grinding and polishing motor for small discs, brushes and baffings. Particularly suitable for gold and silver smiths, opticians, tooth laboratories, music intstrument engineers, ...
The complete shaft is hollow, drill diameter 9mm.
The shaft end is lengthened, diameter 20mm and equipped with a conus B 12 - for attaching thread crests, chucks or flanges for small grinding discs, ...
Also the bendable shaft (Article 3070) can be mounted.
By request the motor can also be delivered with a different shaft, e.g. with smooth shaft 15 mm diameter for using the HAMAG quick clamp flanges.
Also deliverable with foot switch for toggling right and left rotation and / or with an inverter for stepless speed control.
from 1 from € 470.00 Incl. 19.00% VAT
Put on thread crests
with cone B 12 to our BAA Motor for quick put on of buff, filt discs or brushes with wooden or plastic core, ...
For right or left rotating motors.
To the left side of the motors a thread crest with left hand thread is attached. To the right side a thread crest with right-hand thread.
from 1 from € 35.00 Incl. 19.00% VAT
with cone B 12 for polishing motor BAA or other motors with this cone. For mounting of small grinding and polishing discs with 10 mm disc center hole.
from 1 from € 19.00 Incl. 19.00% VAT
BAA Flangefrom 1 from € 19.00 Incl. 19.00% VAT
Precision drill chuck for polishing motor BAAfrom 1 from € 57.00 Incl. 19.00% VAT
Combinable Gemstoneworker for Hobby- and Professional grinding.
Length 45 cm, height 22 cm, weight 14 kg.
Rigid, long-life, made of cast iron. Designed for extreme continuous operation (particularly quiet).
On 4 fold ballraced, grinded, stainless steel Welle (concentricity 1/100 mm) disc change is possible within seconds due to the patented quick clamp flange.
Accessories - like saw, beveling und wet grinding device - can be quickly attached to the bearing shield flange with 60 mm diameter using 1 clamping bolt at both sides.
2 speeds - 700 U/min or 1400 U/min, with 2 flanging possibilities for accessories, smooth shaft Ø 15 mm, pole toggle switch, plug with cord and foot.
from 1 from € 726.00 Incl. 19.00% VAT
Multimotor Exportfrom 1 from € 667.00 Incl. 19.00% VAT
Polierspitzefrom 1 from € 79.00 Incl. 19.00% VAT