All
Top seller
-
Book "Die Farbigkeit des schwarzen Turmalins"
from 1 from € 39.50 Incl. 19.00% VAT -
Book "Edle Steine schleifen"
from 1 from € 16.60 Incl. 7.00% VAT -
3-phase asynchronous motor with squirrel cage rotor: 4001,4002,4003,4004,4005,4006,4007,4008,4009,4010,4011,4012,4013,4014,4015,4016,4017,4018,4019, 4101,,4102,4103,4104,4105,4106,4107,4108,4109,4110,4111,4112,4113,4114,4115,4116,4117,4118,4119,4120
3-phase norm motor per DIN-IEC, VDE 0530.
Isolation class F (155 °C maximum conductor temperature)
Rated power at permanent operation per DIN VDE 0530 Teil 1.
Degree of protection IP 55.
Equipped with high quality, whole-life lubricated ball bearings of renowned manufacturers.
And radial fans of plastic or Aluminium.Terminal box on top at foot construction type.
Can be delivered in flange construction type on 5 % extra cost.
from 1 from € 66.00 Incl. 19.00% VAT -
SiC Schleifkörper
from 1 from € 8.20 Incl. 19.00% VAT -
Filler
Small plastic parts approximately 2 mm to 4 mm as addition to drum machines and spirators. For refilling of the containers when polishing soft and sensitive stones.
Content: 1/2 Kg
from 1 from € 6.20 Incl. 19.00% VAT -
Filt disc
to elastic grinding unit. With this disc the ball bearing stock countershaft can be transformed to a elastic band grinding unit with a few simple steps.
Can be delivered on quick clamp flange too.
Filt disc gray.
Density 600.
Width 25 mm,
Hole 20 mm
from 1 from € 24.00 Incl. 19.00% VAT -
Keilriemenscheibe
from 1 from € 54.00 Incl. 19.00% VAT -
Schleifband
from 10 from € 3.40 Incl. 19.00% VAT -
Schnellspannflansch HAMATIC
from 1 from € 75.60 Incl. 19.00% VAT -
Schnellspannflansch HAMATIC
from 1 from € 68.10 Incl. 19.00% VAT -
Polierspitze
from 1 from € 99.00 Incl. 19.00% VAT -
Multimotor Export
from 1 from € 768.00 Incl. 19.00% VAT -
Multimotor Export
Combinable Gemstoneworker for Hobby- and Professional grinding.
Length 45 cm, height 22 cm, weight 14 kg.Rigid, long-life, made of cast iron. Designed for extreme continuous operation (particularly quiet).
On 4 fold ballraced, grinded, stainless steel Welle (concentricity 1/100 mm) disc change is possible within seconds due to the patented quick clamp flange.Accessories - like saw, beveling und wet grinding device - can be quickly attached to the bearing shield flange with 60 mm diameter using 1 clamping bolt at both sides.
2 speeds - 700 U/min or 1400 U/min, with 2 flanging possibilities for accessories, smooth shaft Ø 15 mm, pole toggle switch, plug with cord and foot.
from 1 from € 726.00 Incl. 19.00% VAT -
Precision drill chuck for polishing motor BAA
from 1 from € 66.00 Incl. 19.00% VAT -
BAA Flange
from 1 from € 24.00 Incl. 19.00% VAT -
BAA Flange
with cone B 12 for polishing motor BAA or other motors with this cone. For mounting of small grinding and polishing discs with 10 mm disc center hole.
from 1 from € 24.00 Incl. 19.00% VAT -
Put on thread crests
with cone B 12 to our BAA Motor for quick put on of buff, filt discs or brushes with wooden or plastic core, ...
For right or left rotating motors.
To the left side of the motors a thread crest with left hand thread is attached. To the right side a thread crest with right-hand thread.
from 1 from € 48.00 Incl. 19.00% VAT -
Polishing motor BAA workbench motor
A versatile grinding and polishing motor for small discs, brushes and baffings. Particularly suitable for gold and silver smiths, opticians, tooth laboratories, music intstrument engineers, ...
The complete shaft is hollow, drill diameter 9mm.
The shaft end is lengthened, diameter 20mm and equipped with a conus B 12 - for attaching thread crests, chucks or flanges for small grinding discs, ...
Also the bendable shaft (Article 3070) can be mounted.
By request the motor can also be delivered with a different shaft, e.g. with smooth shaft 15 mm diameter for using the HAMAG quick clamp flanges.
Also deliverable with foot switch for toggling right and left rotation and / or with an inverter for stepless speed control.230 V
0.37 kW
from 1 from € 540.00 Incl. 19.00% VAT -
90-degree-support for grinding plate
90° support steel, adjustable height, ideal for grinding angled faces.
With flange beam, bolt and angular rail, "Hammerschlag" lacquered.
Suitable for Multimotor Export and Simplex with grinding pad 250 mm diameter (article number 3260).
from 1 from € 93.30 Incl. 19.00% VAT -
Diamond paste with natural diamonds: 2190,2191,2192,2193,2194,2195,2196,2197,2198,2199,2200,2201,2202,2203,2204,2205,2206,2207,2208,2209,2210,2211,2212,2213
Concentration N (high diamond concentration)
oil / lapid soluble.
For finest polish of gemstones.
from 1 from € 46.80 Incl. 19.00% VAT -
Sharpening stone
from 1 from € 25.20 Incl. 19.00% VAT -
Diamond faceting disc D* sintered
Sintered Diamond disc, where the Diamond granules are embedded in a 0.5 mm thick Bronze cover. Thereby the life-time is significantly increased compared to galvanically bound discs.
Outer diameter 150 mm; Cover width: 32,5 mm. The center hole is 1/2" (12,7 mm) by default, and can be changed on request.
Allows a clean grinding, because water is only used dropwise.
In the center is a recess, in which the different polishing inserts article numbers 2000..2030 can be fitted.
Different grain sizes available.
Preis auf Anfrage!
from 1 from € 408.00 Incl. 19.00% VAT -
Grinding sheet
from 1 from € 1.80 Incl. 19.00% VAT -
Galvanic Diamond Grinding disc S
Dimensions: 150 mm (outer diameter) x 32,5 mm (cover width)
With this heavy steel disc the diamond granules are bonded in a layer of nickel.
The center bore by default is 1/2" (12.7 mm), can be changed on request.Diamond discs allow a clean grinding, because water is used only dropwise.
There is a recess in the center in which the different polishing inserts article numbers 2000..2030 may be placed.
Different grain sizes available.
Price on request!(Figure similar)
from 1 from € 0.00 Incl. 19.00% VAT -
Perforated diamond disc galvanic for thin section
from 1 from € 186.00 Incl. 19.00% VAT -
Area grinding pad
On lathe turned Aluminium grinding pad, diameter 250 mm, on quick clamping flange with rubber support.
For all Multimotors and the special countershaft. For bonding of grinding sheets (glue article number 2350).
Suitable for working wood, plastic, aluminium, steel and many more materials.
In connection with the 90° support a must-have for every workshop.
Aluminium grinding pad, 250 mm diameter with flange for either Simplex or Export.
from 1 from € 137.50 Incl. 19.00% VAT -
Galvanische Diamant-Schleifscheibe D*
from 1 from € 0.00 Incl. 19.00% VAT -
Galvanische Diamantschleifscheibe
from 1 from € 72.00 Incl. 19.00% VAT -
Aluminium support disc
To article numbers 1941..1947.
Aluminium carrier disc with diameter 150 mm, 8 mm thick and center hole 1/2".Required only for the diamond discs made of 1 mm steel sheet.
from 1 from € 36.60 Incl. 19.00% VAT -
Diamond drill with holder and ejector: 4300,4310,4320,4330,4340,4350,4360,4370,4380,4390,4400,4410,4420,4430,4440,4450,4460,4470
The bit is of diamond grain, such that the life time is not comparable with other only coated bits.
These drills have a hundred-fold life time if compared against others because the drill bit can be used till the end. (A merely coated drill is worthless once the few dimond granules on the front side are broken out).
Shaft with respective drill diameter 30 mm long and at the back a thread of M4.
Can be screwed in flushing head (article number 4200).
from 1 from € 26.00 Incl. 19.00% VAT -
Dopp-pin single flat
Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.
from 1 from € 4.70 Incl. 19.00% VAT -
Keilriemenscheibe
from 1 from € 66.00 Incl. 19.00% VAT -
Diamond hollow drill sintered
(Diamond grain in bronze bond)
Drilldepth standard 40 mm.
Thickness coating 6 mm, wall 1 mm.
Machine clamp system Belgian thread R 1/2".
Diamond concentration C 75.
Drill depth on diameter 6 mm up to 160 mm deliverable (request price)
Drill depth on diameter 10 mm up to 200 mm available (request price)
Drill depth on diameter 20 mm up to 250 mm deliverable (request price)
Other drill depth on diameter 180 mm up to 250 mm on request.
These drills can be delivered with approximate diameter 13 mm with cylindrical shaft (€ 6,- extra cost).
from 1 from € 99.60 Incl. 19.00% VAT -
Wasseranschluß mit Schlauch
from 1 from € 25.00 Incl. 19.00% VAT -
Dopp pin single special dimensions
Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.
from 1 from € 8.10 Incl. 19.00% VAT -
Elastic belt grinding unit
for grinding belts of 25 mm width and 1000 mm length. The grinding belt thereby runs on 2 filt discs on quick clamping flange (one on the motor shaft and the other on the ball bearing countershaft).
The tension of the grinding belt can be adjusted fix. Or the grinding belt is tensioned by spring force, such that it yields when grinding.The second shaft end of the ball bearing countershaft may be used for different purposes, in which the grinding belt is used as drive.
Additionally the countershaft is rotatable to every orientation around the axis of the motor shaft (sitting or standing work).
Allows grinding of almost all materials. Recommended for wood, plastic and metal processing.
Mountable to the Multimotors SIMPLEX and EXPORT.
from 1 from € 468.00 Incl. 19.00% VAT -
Drill flushing head
Small drill flushing head for diamond drills 0.7..10 mm diameter.
Can be clamped into common commercially available bench drills with chuck and is compatible for drilling machines with holder and ejector. The mounting shaft is 6 mm.
from 1 from € 197.00 Incl. 19.00% VAT -
Kugellagervorgelege Simplex/Export
from 1 from € 483.00 Incl. 19.00% VAT -
Galvanic hollow drill bit
Because the drill bit is made completely of diamond granules, the life-time compared to other only coated (and that sparsely) diamond bits is hundred-fold higher, because the drill can be used till the end.
(A merely coated drill is worthless once the few diamond granules at the front side are broken out.)
The shaft is cylindrical with the respective drill diameter.
Drill length approximately 30..40 mm.
Can be clamped into every chuck.
Without holder and ejector.
from 1 from € 48.00 Incl. 19.00% VAT -
Diamond cut disc sintered
Diamond grain in bronze bond.
These cut discs suit optimally to cut all minerals and stones. They have a very high lifetime and result in very clean cuts.
The coating thickness is 10 mm.
from 1 from € 93.30 Incl. 19.00% VAT -
Kreissäge-Schnellspannflansch
from 1 from € 75.00 Incl. 19.00% VAT -
Diamond cut disc mechanical
Diamond grain pressed mechanically.These affordable cut discs suit especially cutting of gemstones up to hardness levels 7 to 8.
Please choose desired disc diamaeter, cover thickness, cut width and drill diameter.
from 1 from € 30.30 Incl. 19.00% VAT -
Fence scale
with clamping unit for circular saw (article number 3100) as a right side stop.
from 1 from € 53.00 Incl. 19.00% VAT -
Dopp pin single V-groove
Available diameter 4 / 6 / 8 / 10 / 12 mm
Please state the desired diameter.
from 1 from € 4.70 Incl. 19.00% VAT -
Polishing powder Cer-oxide
from 1 from € 9.80 Incl. 19.00% VAT -
Polishing powder Aluminium oxide
The polishing powder is mixed with a bit water in a bowl and is applied with a brush to the polishing discs.
Al-oxide for all kinds of stone.
from 1 from € 4.10 Incl. 19.00% VAT -
Kreissäge-Einheit
from 1 from € 450.00 Incl. 19.00% VAT -
Schwabbelscheibe
from 1 from € 21.10 Incl. 19.00% VAT